E-mail: info@waterri.com

WATERRI.COM

Toll Free: 1-800-767-8731
About us

Products and Services

Water Testing

Well Drilling

Hydrofracturing

Well Chlorination

Radon mitigation

Davey Booster Pumps

Drinking Water Standards

Terms and Definitions

Directions

Home
Call 1-800-767-8731 to talk to our experts on Radon related issues

All about Radon

Radon is a radioactive gas that cannot be seen, smelled or tasted. It is the product of natural decay of radioactive uranium in the rocks and soil around us. It can be found almost everywhere on earth and therefore Radon gas is found almost everywhere. Radon gas is a source of more radiation than all other natural causes - cosmic rays, internal sources and man-made radiation-X rays, nuclear medicine and consumer products put together.

Radon gas that comes out into open air dissipates very quickly and is no threat. Radon gas that comes into a home can accumulate to dangerous levels. Long-term exposure to high levels of radon poses a very real health threat.

Important Facts on Radon:

  • Radon is the second leading cause of lung cancer
  • Nearly one in 15 homes in the U.S. has a high level of indoor Radon
  • The U.S. Surgeon General and EPA recommend all homes be tested for Radon
  • Homes with high Radon levels can be fixed
Radon in water
Radon being soluble in water enters the underground water supply easily. All ground water has radon and some have very high concentrations. Radon that enters a home through the water supply escapes from the water when flushed, heated or sprayed in showers, dishwashers and clothes washers.

In homes with a private well, radon entering from the water can raise the radon in air to very high levels and breathing this air for long periods can increase the risk of lung cancer.


Radon concentrations commonly are much higher in water than in air. As a general rule, a measurement of 10,000 pCi/L radon in well water will contribute to 1 pCi/L throughout the household Air.

AIRaiderTM Diffused Bubble Aeration Systems
The AIRaiderTM series of Diffused Bubble Aeration Systems are effective, efficient and dependable for radon and VOC removal.

The AIRaiderTM Systems reduce and/or remove the following from water:
  • Radon
  • Benzene
  • Dicholorethane
  • Trichloroethylene
  • Vinyl Chloride
  • Carbon Dioxide
  • MTBE
  • Toluene
  • THMs
  • Hydrogen Sulfide and more...
The AIRaiderTM's reduction capabilities are based on straight flow-through performance. AIRaiderTM does not require recirculation, a long settling period or a large holding to achieve effectiveness.

AIRaider 433 - Effective and Dependable for the removal of Radon and VOCs
Quality and Reliability
Price : $3995.00
(Includes Tax and Installation)


Installed with a Goulds Pump and a Well-X-Trol Tank

Rhode Island Radon Mitigation Contractor License No: RCL-015


AIRaider 433 System Specifications

Aeration Tank Size: 19.75"W x 31.25"L x 35"H (44 gal.)
Aeration Tank Material: FDA Approved Polyethylene
Regenerative Blower: 0.5 hp, 115V/7.4 amp OR 230V/3.65 amp
Control Panel: UL Listed, 115V/230V
Vent Line (not included): 2" Schedule 40 PVC
Plumbing: 3/4" or 1"
Flow Rate: up to 20 gpm
Standard Pressure Tank Size: 20 Gallons Well-X-Trol Pressure Tank
Jet Pump: 1/2 hp, 115V/6.7 amp, Goulds Jet Pump
Radon and VOC Reduction: up to 99+%

AIRaider 201

Price: $2995.00
(Includes Tax and Installation)
System Specifications
Aeration Tank Size: 19.75"W x 31.25"L x 35"H (44 gal.)
Aeration Tank Material: FDA Approved Polyethylene
Regenerative Blower: 0.11 hp, 115V/1.2amp
Control Panel: UL Listed, 115V
Vent Line (not included): 2" Schedule 40 PVC
Plumbing: 3/4"
Flow Rate: up to 7 gpm
Standard Pressure Tank Size: 20 Gallons Well-X-Trol Pressure Tank
Jet Pump: 1/2 hp, 115V/6.7 amp, Goulds Jet Pump
Radon and VOC Reduction: up to 85+%

Radon Removal using Carbon Filtration

PRICE: $1500.00
(Includes Tax and Installation)

Two 12x48 mineral tanks with 2 Cu. ft of Coconut Shell Activated Carbon each for a total of 4 Cu.ft specially designed for the removal of lower concentrates of Radon gases in Water.

Installation includes a before sampling port, a secondary port between tank 1 and tank 2 and a final sampling port after the final tank. The purpose of these sampling ports is to develop information on the system’s performance.